INSPECTION DE LECTURE DES PID/DONNEES


BHE050201026W30

1. Brancher le WDS ou équivalent sur le DLC-2.

2. Mesurer la valeur du PID.

Remarque
• Effectuer l'inspection des pièces pour le dispositif de sortie après l'inspection du PCM.
• La fonction LECTURE DES PID/DONNEES lit la valeur calculée des signaux d'entrée/sortie dans le TCM. Par conséquent, si une valeur contrôlée d'un appareil de sortie n'est pas dans les limites spécifiées, il faut inspecter la valeur contrôlée de l'appareil d'entrée correspondant au contrôle de sortie. Puisqu'une anomalie d'un appareil de sortie n'est pas directement indiquée comme une anomalie de la valeur contrôlée pour l'appareil de sortie, il faut inspecter l'appareil de sortie individuellement à l'aide de la fonction de simulation, etc.

Point de contrôle (définition)

Unité/Etat

Etat/Spécification

Action

Borne du TCM

24B_Duty
(Shift solenoid B)
%
2 or 4GR: 0%
• Other: 99%
• Inspect the shift solenoid valve B.
2S
BOO_TCM
(Brake switch)
ON/OFF
• Brake pedal is depressed: ON
• Brake pedal is released: OFF
• Adjust the brake pedal.
• Inspect the brake switch.
1G
CPP/PNP
(P/N position switch)
Drive/Neutral
• P or N position: Neutral
• R, D or M range: Drive
• Inspect the TR switch.
1D, 2B
DTC_CNT
(Number of DTCs detected)
N/A
• DTCs is detected: 1-255
• No DTCs are detected: 0
• Inspect the DTCs.
N/A
DWN SW
(Down switch)
ON/OFF
• M range, downshift: ON
• Other: OFF
• Inspect the selector lever component.
2D
ECT TCM
(ECT sensor)
°C, °F
• Indicates engine coolant temperature
• Inspect the ECT sensor.
• Inspect the PCM.
N/A
FDPDTC
N/A
• Pending code that caused FFD storage
N/A
N/A
GEAR
1st/2nd/3rd/4th
1GR: 1st
2GR: 2nd
3GR: 3rd
4GR: 4th
• Inspect the following PIDs: 24B_Duty, HC_Duty, LRB_Duty, TCCC
N/A
GEAR_RA
(Gear ratio)
N/A
1GR: 2,785
2GR: 1,545
3GR: 1,000
4GR: 0,694
• Reverse: 2,272
• Inspect the following PIDs: 24B_Duty, HC_Duty, LRB_Duty, OP_SW_24B, OP_SW_HC, OP_SW_LRB, TCCC
N/A
HC_Duty
(Shift solenoid C)
%
3 or 4GR: 0%
• Other: 99%
• Inspect the shift solenoid valve C.
2V
LRB_Duty
(Shift solenoid F)
%
• R position or 1GR at M range: 0%
• Others: 99%
• Inspect the shift solenoid valve F.
2P
LU_Duty
(TCC solenoid)
%
• TCC operation off: 0%
• TCC operation on: 99%
• Inspect the TCC shift solenoid valve.
2W
MNL SW
(M range switch)
ON/OFF
• M range: ON
• Other: OFF
• Inspect the selector lever component.
1E
OP_SW_24B
(Oil pressure switch B)
ON/OFF
2 or 4GR: ON
• N position: OFF
• Inspect the oil pressure switch B.
2A
OP_SW_HC
(Oil pressure switch C)
ON/OFF
3 or 4GR: ON
• N position: OFF
• Inspect the oil pressure switch C.
2F
OP_SW_LRB
(Oil pressure switch F)
ON/OFF
• R position: ON
• N position: OFF
• Inspect the oil pressure switch F.
2H
OSS
(Output shaft speed signal)
rpm
• Indicates output shaft speed
• Inspect the vehicle speed sensor
2K
PCSV
(Pressure control solenoid)
ON/OFF
• Line pressure high: ON
• Line pressure low: OFF
• Inspect the pressure control solenoid valve.
2X
RPM
(Engine speed)
rpm
• Engine speed 1,000 rpm: 1,000 rpm
• Inspect the TCM.
N/A
TCCC
(Shift solenoid A)
%
4GR: 99%
• Other: 0%
• Inspect the shift solenoid valve A.
2Y
TFT
(ATF temperature)
°C, °F
• ATF 20 °C {68 °F}: 20 °C {68 °F}
• ATF 80 °C {176 °F}: 80 °C {176 °F}
• Inspect the TFT sensor.
2J
TFTV
(ATF temperature signal voltage)
V
• ATF 20 °C {68 °F}: 1,55 V
• ATF 60 °C {140 °F}: 0,7 V
• Inspect the TFT sensor.
2J
THOP
(Throttle position)
%
• CTP: 0%
• WOT: 100%
• Inspect the TCM.
N/A
TR
(Transmission range)
R/N/D
• R position: R
• N position: N
• D range: D
• Inspect the TR switch.
2B, 2C, 2E
TRD
(D range switch)
ON/OFF
• D range: ON
• Except D range: OFF
• Inspect the TR switch.
2E
TRR
(R position switch)
ON/OFF
• R position: ON
• Except R position: OFF
• Inspect the TR switch.
2C
TSS
(Turbine sensor)
rpm
• Ignition switch at ON position (engine off): 0 rpm
• Idle: 700-800 rpm
• Inspect the turbine sensor
2G
UP SW
(Up switch)
ON/OFF
• M range, upshift: ON
• Other: OFF
• Inspect the selector lever component.
2I
VPWR
(Battery voltage)
V
• Ignition switch at ON position: B+
• Engine running: B+
• Inspect the ignition switch.
• Inspect the battery.
1A, 2Z, 2AA
VSS
(Vehicle speed)
km/h, mph
• Indicates vehicle speed
• Inspect the VSS.
• Inspect ABS HU/CM.
• Inspect DSC HU/CM.
• Inspect PCM.
N/A